Related Articles What Are the Differences Between the Two USB Plugs on an External Hard Drive? Simply turn on your PC, press the Del key a few times (or look for a message telling which key to press to enter Setup) and the BIOS should appear. HowStuffWorks Tech Tech Toggle navigation Follow us Facebook YouTube Twitter Pinterest NOW Adventure Animals Auto Culture Entertainment Health Home & Garden More Lifestyle Money Science Tech Video Shows Quizzes Lifestyle Money Yükleniyor... Source
Attach the wrist strap to the metal chassis of your computer. EDIT Edit this Article Home » Categories » Computers and Electronics » Hardware » Internal Components ArticleEditDiscuss Edit ArticleHow to Configure Master and Slave in BIOS for Two Hard Drive Disk Also, the slave drive is attached to the connector near the middle of the IDE ribbon cable. Peripherals connected to a bus in a computer system.
thanks in advance =) 4 answers Last reply Dec 20, 2011 More about master slave sata drives rolli59Dec 19, 2011, 1:02 AM There is a jumper on the IDE drive so You will see some kind of stripe running down the side of the cable that will indicate pin 1. For example, DOS/Windows will assign drive letters to the master drive before the slave drive.
Kapat Evet, kalsın. Master Slave Hard Drive Jumper Settings How to Tether Your Droid in Ubuntu An Easy Way to Wipe Your Hard Drive How to Restrict Bandwidth in a Linksys Wireless Router How to Attach a Wireless Router to It is also a good solution for backing-up files. https://www.techwalla.com/articles/what-is-the-difference-between-master-slave-hard-drives If you want to do that you'll just have to make sure that it's plugged into the right part of the cable.
Troubleshooting No hard drives show up: Do you have two drives on the cable? Master Slave Computer Setup The slave drive must have either the master jumper removed or a special slave jumper set, depending on the drive. Computers without a secondary drive set as a slave drive will store their data on the main (only) hard drive, alongside the operating system.Jumper SettingsA slave (secondary) hard drive needs no Tech Reviews Tech News Tech How To Best Tech Reviews Tech Buying Advice Laptop Reviews PC Reviews Printer Reviews Smartphone Reviews Tablet Reviews Wearables Reviews Storage Reviews Antivirus Reviews Latest Deals
Format the drive. Selecting Device Channels A computer determines if a hard drive is the master or slave depending on the position of the pin jumper next to the cable connection on the drive. Master And Slave Drive Explained If your using Windows 9x (why?) then you'll want to check out bootdisk.com and find something that'll cover your needs. Difference Between Master And Slave Drive One of the reasons why drives don't always "play nicely together" has to do with the Drive Active / Signal Present (/DASP) signal.
Make sure you select quick format or else it'll be a while before you can use the disk. this contact form Can I set my IDE drive as slave if I'm using an IDE to SATA converter? With the correct type of IDE ribbon cable, these drives can be auto configured as master or slave. When using only a single drive on a channel, there are some considerations to be aware of. What Is A Slave Hard Drive
Let's Begin Unpack everything. The only practical difference between master and slave is that the PC considers the master "first" and the slave "second" in general terms. Watch carefully for the initial boot screen to display and tap the necessary key to over-ride the boot process. have a peek here The Four Major Components of a Hard Drive Leaf Group Ltd.
But to select the boot device, you do that in BIOS in the Boot Priority Sequence section.Alternatively (and I'm guessing you do this) you can use a keyboard key just after How To Install A Second Sata Hard Drive In Windows 7 DO NOT put a CD Drive on the same channel as your hard drive! Articles & News Forum Graphics & Displays CPU Components Motherboards Games Storage Overclocking Tutorials All categories Chart For IT Pros Get IT Center Brands Tutorials Other sites Tom's Guide Tom's IT
This is done by giving each device a designation as either master or slave, and then having the controller address commands and data to either one or the other. Yükleniyor... I don't think SATA drives have master/slave configuration but I can't access the IDE master drive when I boot from the SATA drive. Sata Master Slave Oturum aç 177 17 Bu videoyu beğenmediniz mi?
If only one drive is installed, it should always be the master drive. This is done using a jumper on pins on the back of each IDE device to set to either Master or Slave. VGA Connector Types Editor's Picks How to Add USB to VMware The Process Used by Bluetooth to Create a Connection How to Know if a USB Printer Cable Is Working Correctly? Check This Out BUY NOW FREE TRIAL BACKUP & RESTORE For Business » Todo Backup WorkstationBuyTry Todo Backup ServerBuyTry Todo Backup Advanced ServerBuyTry For Home & Home Office » Todo Backup FreeDownload Todo Backup
There are many more performance considerations to take into account when deciding how to jumper your IDE devices, if you are using several different ones on more than one channel. Need more storage space? Dilinizi seçin. Content continues below Your motherboard might have some SATA II ports (running at 3Gb/s) and some SATA III ports.
Click next it's just a summary of what you told it to do. Düşüncelerinizi paylaşmak için oturum açın. For example, this machine I'm on tries to boot first from a floppy disk drive, then one of my optical drives, then one of my hard drives. After installing the additional hard-drive, you will need to change your computer's Basic Input Output System (BIOS) settings to "Master/Slave." Steps 1 Restart your computer.